Lavoisier S.A.S.
14 rue de Provigny
94236 Cachan cedex
FRANCE

Heures d'ouverture 08h30-12h30/13h30-17h30
Tél.: +33 (0)1 47 40 67 00
Fax: +33 (0)1 47 40 67 02


Url canonique : www.lavoisier.fr/livre/environnement/advances-in-steam-turbines-for-modern-power-plants/descriptif_4567294
Url courte ou permalien : www.lavoisier.fr/livre/notice.asp?ouvrage=4567294

Advances in Steam Turbines for Modern Power Plants (2nd Ed.) Woodhead Publishing Series in Energy Series

Langue : Anglais

Coordonnateur : Tanuma Tadashi

Couverture de l’ouvrage Advances in Steam Turbines for Modern Power Plants

Advances in Steam Turbines for Modern Power Plants, second edition,provides a fully revised and updated comprehensive review of steam turbine design, optimization, analysis and measurement. Editor Tadashi Tanuma and his team of expert contributors from around the globe have updated each chapter to reflect the latest research and experiences in the field, to help progress thermal power generation to meet sustainability goals. This book presents modern technologies for the design and development of steam turbines that supply affordable, reliable and stable power with much lower CO2 emissions.

With the addition of two new chapters on ?Steam turbine mechanical design and analysis for high temperature, large and rapid change of temperature conditions? and ?Steam valves with low pressure losses? this edition will support students, researchers and professional engineers in designing and developing their own economical and environmentally concerned thermal power plants.

Part I Steam Turbine Cycles and Cycle Design Optimization 1. Introduction to steam turbines for power plants 2. Steam turbine cycles and cycle design optimization: the Rankine cycle, thermal power cycles, and IGCC power plants 3. Steam turbine cycles and cycle design optimization: advanced ultra-supercritical thermal power plants and nuclear power plants 4. Steam turbine cycles and cycle design optimization: combined cycle power plants 5. Steam turbine life cycle cost evaluations and comparison with other power systems

Part II Steam Turbine Analysis, Measurement and Monitoring for Design Optimization 6. Design and analysis for aerodynamic efficiency enhancement of steam turbines 7. Steam turbine rotor design and rotor dynamics analysis 8. Steam turbine design for load-following capability and highlyefficient partial operation 9. Analysis and design of wet-steam stages 10. Solid particle erosion analysis and protection design for steam turbines 11. Steam turbine monitoring technology, validation, and verification tests for power plants

Part III Development of Materials, Blades and Important 12. Development in materials for ultra-supercritical (USC) and advanced ultra-supercritical (A-USC) steam turbines 13. Development of last-stage long blades for steam turbines 14. Introduction of new sealing technologies for steam turbines 15. Introduction of advanced technologies for steam turbine bearings 16. Manufacturing technologies for key steam turbine parts

Part IV Turbine Retrofitting and Advanced Applications in Power Generation 17. Steam turbine retrofitting for the life extension of power plants 18. Steam turbine retrofitting for power increase and efficiency enhancement 19. Advanced geothermal steam turbines 20. Steam turbines for solar thermal and other renewable energies 21. Advanced ultra-supercritical pressure (A-USC) steam turbines and their combination with carbon capture and storage systems (CCS) 22. Steam turbine roles and necessary technologies for stabilization of the electricity grid in the renewable energy era 23. Conclusions

Tadashi Tanuma is a Professor at Teikyo University, Japan. He is the head of the Laboratory of Fluid-Structural Simulation and Design in the Strategic Innovation and Research Center. He also works for the Graduate School of Science & Engineering and the Department of Mechanical and Precision System Engineering in Teikyo University.

Professor Tadashi Tanuma began his career as a development mechanical engineer in 1980 at Turbine Factory, Toshiba Corporation, Japan. He led the Turbomachinary Development Group from 1993. Subsequently, he joined the Steam Turbine Design Department in Keihin Product Operations of Toshiba Corporation. He developed and designed Toshiba 52-inch last stage long blade for nuclear power steam turbines and steel 40 and 48-inch last stage long blade for thermal power steam turbines as an aerodynamic engineer and led many research and development programs for steam and gas turbine efficiency enhancement technologies. He was the President of the Gas Turbine Society of Japan (2015).
  • Fully updated to include the latest research and examples from around the globe
  • Includes brand new chapters, case studies, photographs, data, analysis and models
  • Chapters on the design and development of Steam Turbines are written by experienced design engineers who provide first-hand experience and lessons learned.